Image is for reference only, refer to product info for complete details.
Bezel provides flange for flush mounting in panel. Clear plastic face is highly resistant to breakage. Provides undistorted viewing of pointer and scale.
Bezel provides flange for flush mounting in panel. Clear plastic face is highly resistant to breakage. Provides undistorted viewing of pointer and scale.
The Dwyer 2001 Differential Pressure Gauge Features a range of 0-10" w.c. and minor divisions of .20.
Select the Magnehelic® gauge for high accuracy--guaranteed within 2% of full scale--and for the wide choice of 81 models available to suit your needs precisely. Using Dwyer's simple, frictionless Magnehelic® gauge movement, it quickly indicates low air or non-corrosive gas pressures--either positive, negative (vacuum) or differential. The design resists shock, vibration and over-pressures. No manometer fluid to evaporate, freeze or cause toxic or leveling problems. It's inexpensive, too.
The Magnehelic® gauge is the industry standard to measure fan and blower pressures, filter resistance, air velocity, furnace draft, pressure drop across orifice plates, liquid levels with bubbler systems and pressures in fluid amplifier or fluidic systems. It also checks gas-air ratio controls and automatic valves, and monitors blood and respiratory pressures in medical care equipment
Note: May be used with Hydrogen. Order a Buna-N diaphragm. Pressures must be less than 35 psi.
Service | Air and non-combustible, compatible gases (natural gas option available). Note: May be used with hydrogen. Order a Buna-N diaphragm. Pressures must be less than 35 psi |
Wetted Materials | Consult factory |
Housing | Die cast aluminum case and bezel, with acrylic cover, Exterior finish is coated gray to withstand 168 hour salt spray corrosion test. |
Accuracy | ±2% (-HA model ±1) of FS (±3% (-HA ±1.5%) on -0, -100PA, -125PA, -10MM and ±4% (-HA ±2%) on -00, -60PA, -6MM ranges), throughout range at 70°F (21.1°C) |
Pressure Limits | -20 in Hg. to 15 psig.† (-0.677 bar to 1.034 bar); MP option; 35 psig (2.41 bar), HP option; 80 psig (5.52 bar) |
Enclosure Rating | IP67 |
Overpressure | Relief plug opens at approximately 25 psig (1.72 bar), standard gauges only. See Overpressure Protection note on Catalog page |
Temperature Limits | 20 to 140°F (-6.67 to 60°C). -20°F (-28°C) with low temperature option |
Size | 4" (101.6 mm) diameter dial face |
Mounting Orientation | Diaphragm in vertical position. Consult factory for other position orientations |
Process Connections | 1/8" female NPT duplicate high and low pressure taps - one pair side and one pair back |
Weight | 1 lb 2 oz (510 g); MP & HP 2 lb 2 oz (963 g) |
Standard Accessories | Two 1/8" NPT plugs for duplicate pressure taps, two 1/8" pipe thread to rubber tubing adapters and three flush mounting adapterswith screws. (Mounting and snap ring retainer substituted for three adapters in MP & HP gauge accessories) |
Click on a category to view a selection of compatible accessories with the Dwyer 2010 Magnehelic Differential Pressure Gauge (0-10"w.c.).
Service | Air and non-combustible, compatible gases (natural gas option available). Note: May be used with hydrogen. Order a Buna-N diaphragm. Pressures must be less than 35 psi |
Wetted Materials | Consult factory |
Housing | Die cast aluminum case and bezel, with acrylic cover, Exterior finish is coated gray to withstand 168 hour salt spray corrosion test. |
Accuracy | ±2% (-HA model ±1) of FS (±3% (-HA ±1.5%) on -0, -100PA, -125PA, -10MM and ±4% (-HA ±2%) on -00, -60PA, -6MM ranges), throughout range at 70°F (21.1°C) |
Pressure Limits | -20 in Hg. to 15 psig.† (-0.677 bar to 1.034 bar); MP option; 35 psig (2.41 bar), HP option; 80 psig (5.52 bar) |
Enclosure Rating | IP67 |
Overpressure | Relief plug opens at approximately 25 psig (1.72 bar), standard gauges only. See Overpressure Protection note on Catalog page |
Temperature Limits | 20 to 140°F (-6.67 to 60°C). -20°F (-28°C) with low temperature option |
Size | 4" (101.6 mm) diameter dial face |
Mounting Orientation | Diaphragm in vertical position. Consult factory for other position orientations |
Process Connections | 1/8" female NPT duplicate high and low pressure taps - one pair side and one pair back |
Weight | 1 lb 2 oz (510 g); MP & HP 2 lb 2 oz (963 g) |
Standard Accessories | Two 1/8" NPT plugs for duplicate pressure taps, two 1/8" pipe thread to rubber tubing adapters and three flush mounting adapterswith screws. (Mounting and snap ring retainer substituted for three adapters in MP & HP gauge accessories) |
Click on a category to view a selection of compatible accessories with the Dwyer 2010 Magnehelic Differential Pressure Gauge (0-10"w.c.).