- Sign In
- |
- Sign Up
- |
- My Quote (0)
- |
- CART (0)
Easy and reliable, this EV adapter kit tests the functionality and safety of electric vehicle charging stations that comply with SAE-J1772 standards. In addition, this kit comes with a test adapter, type 1 connector and adapter, industrial scopemeter, industrial multimeter, temperature probe, test leads, soft carrying case, etc.
Easy and reliable, this EV adapter kit tests the functionality and safety of electric vehicle charging stations that comply with SAE-J1772 standards. In addition, this kit comes with a test adapter, type 1 connector and adapter, industrial scopemeter, industrial multimeter, temperature probe, test leads, soft carrying case, etc.
Test the safety and performance of type 1, level 1, or level 2 electric vehicle AC charging stations (EVSEs) with this kit which includes a test adapter, digital multimeter, and scopemeter. The adapter simulates the presence of an electric vehicle, and the multimeter allows you to conduct tests to view the output voltage and maximum current of the EV charging station when connected to the adapter. Verify the EVSE charging states (vehicle simulation) by connecting the scopemeter by measuring the control pilot signal output. In addition, verify an EV charging station is wired and functioning effectively after installation for periodic maintenance or troubleshooting.
Features
Test the functionality and safety of electric vehicle charging stations, easily and reliably
Test the safety and performance of type 1 or connector for Tesla™ station, level 1 or level 2 electric vehicle AC charging stations (EVSEs) with the test adapter. This test adapter simulates the presence of an electric vehicle, allowing you to conduct tests in combination with appropriate test instruments such as a digital multimeter or oscilloscope. Use this adapter to verify an EVSE is working properly after installation and during periodic maintenance, or troubleshoot an EVSE if it is not delivering the appropriate charge.
Safety
EVSE charging cables may become damaged over the course of use, increasing electric shock risks to users. Stay protected from and check the risk of electric shock with the GFCI trip test. This function verifies the breaker of the EVSE is connected by detecting ground faults. Additionally, the PE grounding protection pre-test verifies that there is no presence of dangerous voltage on the ground terminal.
Simplicity and convenience
Perform a variety of tests including ground fault checks, insulation of wires, measuring voltage, and duty cycle to see the maximum current available for charging all with one adapter that safely integrates with the Fluke portfolio of test and measurement tools. There is no need to bring an electric vehicle onsite for EVSE troubleshooting: the adapter acts as an electric vehicle when connected to an EVSE for easy performance and maintenance testing.
Applications
Once an EVSE recognizes it is connected to a "car" and is ready for charging, the adapter tests if the EVSE is performing the way it should be.
1. Perform the safety grounding protection pre-test to verify that no dangerous voltage is present in the grounding circuit. If the indicator lights up, it is possible that the electrical wiring has been set up improperly or there is a grounding malfunction. In this instance stop further testing immediately and check for a possible wiring fault of the ground conductor
2. Verify station output voltage using an additional meter, such as the 87V digital multimeter.
3. Verify station maximum preset charge current using CP terminals and a meter with a duty cycle function or an oscilloscope.
4. Simulate the error states as described in the SAE J1772 standard: CP error "E", GFCI trip test, and grounding error.
CP error "E" simulation
The standard SAE J1772 defines Error "E" as a state when the charging station is: disconnected from the vehicle, disconnected from the utility, there is a loss of utility power or the control pilot is short to control pilot reference (ground). This error simulation tests the station to ensure that if there is an issue with the CP of the vehicle, the station and utility will not supply a charge to the vehicle.
GFCI
Each EVSE is required to be equipped with GFCI protection. On many stations, the GFCI protection is fully automatic and does not need a manual reset after the GFCI circuit is tripped.
Ground error (ground fault) simulation
The Ground Error button simulates an interruption of the ground conductor. As a result, the pending charging process is aborted and new charging processes are prevented. Advanced tests such as insulation resistance, power quality, analysis of the control pilot waveform, and loop impedance can also be done using the adapter in conjunction with appropriate test and measurement equipment.
Verifying charging voltage with vehicle simulation
The CP state rotary switch selector simulates various vehicle states when the test adapter is connected to the charging station. Vehicle states are simulated with different resistances connected between CP and PE conductors.
| Input Voltage | UL1/N = 120 V, UL2/N = 120 V, UL1/L2 = 208 V, 60 Hz (three-phase system) UL1/N = 120 V, UL2/N = 120 V, UL1/L2 = 240 V, 60 Hz (single-phase system) ±10% voltage fluctuations from nominal 2 |
| EV Connector | SAE J1772 socket (type 1, 5P single-phase) Connector for Tesla™ station |
| Functions | CP states: A, B, C, D CP error "E": On/off PE error: On/off GFCI test: Yes, test resistor of 2 kΩ connected between L1 and PE, time limitation 40 ms PE pre-test (typical): Visible indication >30 V on PE conductor |
| Outputs (For Test Purpose Only) | Measuring terminals L1, L2/N, PE: Maximum 250 V 50/60 Hz, CAT II 250 V CP signal output terminals: Approximately ±12 V (under normal conditions), in case of wrong wiring or error of the charging station these terminals can be hazardous ≥maximum 250 V against PE |
| Environmental Conditions | Operating temperature: -4 to 104°F (-20 to 40°C) Storage temperature: -4 to 122°F (-20 to 50°C) Operating humidity range: 10 to 85% RH, non-condensing Storage relative humidity: 0 to 85%, non-condensing Operating altitude: 6561' (2000 m) maximum |
| Safety Standards | IEC 61010-1, Pollution Degree 2 IEC 61010-2-030 |
| Measurement Category | CAT II 250 V |
| IP Protection Class | IP54 |
| Electromagnetic Compatibility (EMC) | International: IEC 61326-1: Basic Electromagnetic Environment CISPR 11: Group 1, Class A Group 1: Equipment has intentionally generated and/or uses conductively-coupled radio frequency energy that is necessary for the internal function of the equipment itself. Class A: Equipment is suitable for use in all establishments other than domestic and those directly connected to a low-voltage power supply network that supplies buildings used for domestic purposes. There may be potential difficulties in ensuring electromagnetic compatibility in other environments due to conducted and radiated disturbances. Caution: This equipment is not intended for use in residential environments and may not provide adequate protection to radio reception in such environments. USA (FCC): 47 CFR 15 subpart B. This product is considered an exempt device per clause 15.103. |
| Internal Power Consumption | 2 W maximum |
| Dimensions | Approximately 8.66 x 4.33 x 1.77" (220 x 110 x 45 mm) without cable assembly |
| Weight | Approximately 16.4 lbs (7.4 kg) |
Conveniently test the function and safety of electric vehicle charging stations with this charging station adapter that comes complete with a type 1 connector and cable. While simulating the presence of an electric vehicle, this adapter performs a variety of tests and provides easy performance and maintenance testing.
Solve problems fast and deliver accurate and advanced troubleshooting capabilities that can handle complex signals. Additionally, this industrial multimeter with temperature is ideal for troubleshooting motor drives, plant automation, power distribution, and electromechanical equipment.
Work with confidence with the oscilloscope that offers simplified testing, more insight, faster electro-mechanical troubleshooting, and comes with 40 MHz of bandwidth. Conveniently measures voltage, current, power waveforms and automatically displays critical numerical readings.
Provides convenience and variety for test lead configurations by attaching clips, hooks, and grabbers as needed.
Click on a category to view a selection of compatible accessories with the Fluke FEV100 Electronic Vehicle Charging Station Adapter Kit with multimeter and scopemeter, 250 V, 50/60 Hz.
| Input Voltage | UL1/N = 120 V, UL2/N = 120 V, UL1/L2 = 208 V, 60 Hz (three-phase system) UL1/N = 120 V, UL2/N = 120 V, UL1/L2 = 240 V, 60 Hz (single-phase system) ±10% voltage fluctuations from nominal 2 |
| EV Connector | SAE J1772 socket (type 1, 5P single-phase) Connector for Tesla™ station |
| Functions | CP states: A, B, C, D CP error "E": On/off PE error: On/off GFCI test: Yes, test resistor of 2 kΩ connected between L1 and PE, time limitation 40 ms PE pre-test (typical): Visible indication >30 V on PE conductor |
| Outputs (For Test Purpose Only) | Measuring terminals L1, L2/N, PE: Maximum 250 V 50/60 Hz, CAT II 250 V CP signal output terminals: Approximately ±12 V (under normal conditions), in case of wrong wiring or error of the charging station these terminals can be hazardous ≥maximum 250 V against PE |
| Environmental Conditions | Operating temperature: -4 to 104°F (-20 to 40°C) Storage temperature: -4 to 122°F (-20 to 50°C) Operating humidity range: 10 to 85% RH, non-condensing Storage relative humidity: 0 to 85%, non-condensing Operating altitude: 6561' (2000 m) maximum |
| Safety Standards | IEC 61010-1, Pollution Degree 2 IEC 61010-2-030 |
| Measurement Category | CAT II 250 V |
| IP Protection Class | IP54 |
| Electromagnetic Compatibility (EMC) | International: IEC 61326-1: Basic Electromagnetic Environment CISPR 11: Group 1, Class A Group 1: Equipment has intentionally generated and/or uses conductively-coupled radio frequency energy that is necessary for the internal function of the equipment itself. Class A: Equipment is suitable for use in all establishments other than domestic and those directly connected to a low-voltage power supply network that supplies buildings used for domestic purposes. There may be potential difficulties in ensuring electromagnetic compatibility in other environments due to conducted and radiated disturbances. Caution: This equipment is not intended for use in residential environments and may not provide adequate protection to radio reception in such environments. USA (FCC): 47 CFR 15 subpart B. This product is considered an exempt device per clause 15.103. |
| Internal Power Consumption | 2 W maximum |
| Dimensions | Approximately 8.66 x 4.33 x 1.77" (220 x 110 x 45 mm) without cable assembly |
| Weight | Approximately 16.4 lbs (7.4 kg) |
Conveniently test the function and safety of electric vehicle charging stations with this charging station adapter that comes complete with a type 1 connector and cable. While simulating the presence of an electric vehicle, this adapter performs a variety of tests and provides easy performance and maintenance testing.
Solve problems fast and deliver accurate and advanced troubleshooting capabilities that can handle complex signals. Additionally, this industrial multimeter with temperature is ideal for troubleshooting motor drives, plant automation, power distribution, and electromechanical equipment.
Work with confidence with the oscilloscope that offers simplified testing, more insight, faster electro-mechanical troubleshooting, and comes with 40 MHz of bandwidth. Conveniently measures voltage, current, power waveforms and automatically displays critical numerical readings.
Provides convenience and variety for test lead configurations by attaching clips, hooks, and grabbers as needed.
Click on a category to view a selection of compatible accessories with the Fluke FEV100 Electronic Vehicle Charging Station Adapter Kit with multimeter and scopemeter, 250 V, 50/60 Hz.
